My favorites

Toroidal inductor calculator

Estimate turns, winding envelope, copper usage and DC resistance from core and wire parameters.

1. Design goals

Loaded design parameters from this link.

Installation limits: Ø ≤ 100 mm · H ≤ 100 mm · Hole ≥ 2 mm

2. Core and inductance

Select a manufacturer, material series and model, or search across manufacturers. Missing parameters and bias curves are not inferred. (6420)

Matching models: 4626 · Showing first 100; refine search for more

Catalog parameters · Selected model source

The source does not specify coated limits. Confirm finished core dimensions before relying on the envelope estimate.

The catalog does not specify AL tolerance. Turns use nominal AL; tolerance bounds are unverified. Enter a confirmed tolerance if available.

Micrometals · HF-109160-2 · 26.92 × 14.73 × 18 mm · AL 320

View / edit core parameters

Changing core dimensions or AL switches to custom; no bias curve is assumed from a material name.

3. Winding and operating conditions

Insulated diameter is an estimate: bare diameter + 0.06 mm. Confirm with the wire supplier.

Parallel wires, leads and winding settings

4. Design estimate

Turns
15
Flat envelope L × W × H
28.64 × 28.64 × 19.72 mm
Installed wire (all strands)
0.86 m
Copper mass
3.89 g

Geometry: fits current space limits

Bias data: Unavailable · Temperature: Not assessed

Target → integer-turn inductance: 68 → 72 μH

Resistance, losses and all results
Layers
1
Zero-bias inductance
72 μH
AL tolerance range
Not verified
Inductance at working current
Not verified
Flat envelope L × W × H
28.64 × 28.64 × 19.72 mm
Remaining hole
13.01 mm
Installed wire (all strands)
0.86 m
Wire with allowance
0.91 m
Copper mass
3.89 g
Core + copper mass
Not verified
DC resistance at 20°C
29.61 mΩ
DC resistance at temperature
34.27 mΩ
DC copper loss
0.308 W
Current-density reference
2.01 A
Actual current density
5.97 A/mm²
Top and side view (schematic)Ø 28.64 mmH 19.72 mm

The catalog does not specify AL tolerance. Turns use nominal AL; tolerance bounds are unverified. Enter a confirmed tolerance if available.

Evidence and winding feasibility

Core parameters from manufacturer catalog; Turns, resistance and copper mass are calculated; envelope and packing are geometric estimates. Parallel wires are side by side; leads, mounts and lead exits are excluded.

AL tolerance: Unknown; nominal inductance only · Core mass: Unknown · Finished wire diameter: Provisional

Meets geometry and space limits; winding process requires verification.

Target → integer-turn inductance: 68 → 72 μH · Flat L×W×H: 28.64 × 28.64 × 19.72 mm

Operating / current-density reference: 3 / 2.011 A. Reference current is not a current rating.

Bias-curve current: — A · — means no valid model-specific curve. This is not a thermal current rating.

Save / compare / share
Calculation assumptions

Geometric estimate: concentric layers, side-by-side equal parallel strands, rectangular core cross-section and even coverage. Flat dimensions exclude leads, bobbins, mounting and manufacturing clearance. Wire weight is copper only; total excludes enamel and added insulation. Equal current sharing is assumed.

Current-density reference is not a rated current. Thermal rise, AC copper loss, core loss and insulation ratings are not verified. Validate with a physical sample at the actual frequency, ripple and cooling conditions.

Bias results use a digitized typical KDA curve (1–1,000 Oe, approximate log interpolation), not a guaranteed minimum curve. AL tolerance is applied independently; loaded minimum is a planning estimate. No extrapolation. Zero-bias AL assumes the manufacturer test conditions; uneven winding may differ.

Manufacturer data and method

Micrometals HF-109160-2 · Magnetics — Powder core calculations

Saved designs and comparison

Drafts save in this browser; save up to 4 designs. Clearing browser data deletes them; export files for another device.

DesignL / ITurns/layersOD×H / hole mmWire m / copper gDCR Ω / DC loss WLoaded L μHActions
High-frequency and steady-state thermal estimate

Single-winding storage/filter inductors with triangular ripple; not common-mode chokes or transformers. AC resistance factor, core loss density and thermal resistance require manufacturer, simulation or measured evidence.

Evidence has not been confirmed.

Copper skin depth: 0.225 mm · Ripple RMS: 0 A

At entered winding temperature: copper including ripple / core / total loss: 0.308 / — / — W

Steady-state temperature: — °C

Total temperature requires evidence, core loss and thermal resistance. Model includes copper resistance feedback with constant core loss and thermal resistance. Skin depth does not model proximity effect. Results are not a current rating or safety certification.

15 turns · Results

Questions, examples and engineering limits

Estimate toroid turns, winding space and resistance using core and wire data. Check AL, insulation diameter and sourced bias data before selection.

Content updated:

How is Toroid Inductor Calculator: Core, Turns and Winding calculated?

Use L = AL × N². Estimate toroid turns, winding space and resistance using core and wire data. Check AL, insulation diameter and sourced bias data before selection.

Sources: mag-inc.com [1]

How do I calculate this example: AL = 100 nH/N², N = 20?

L = 40000 nH = 40 µH. This is a calculated example under the model stated above; it is not a measured component specification.

Which units does Toroid Inductor Calculator: Core, Turns and Winding use?

nH/N², µH, mm, Ω, A. Convert prefixes before substituting values; keep the input and output units attached to every number.

Sources: mag-inc.com [1]

Is nominal inductance constant at every current?

No. DC bias, temperature and measurement frequency can change inductance. Use the manufacturer’s curves for the selected part rather than assuming a constant value.

Sources: coilcraft.com [1]

Can this result predict temperature rise?

No. Temperature rise also requires loss data, mounting, airflow and a validated thermal model. A calculated electrical value is not a thermal qualification.

Sources: coilcraft.com [1]

Should winding fit use bare or insulated wire diameter?

Use insulated outside diameter for physical fit and bare copper diameter for conductor area and DC resistance. Packing and winding technique introduce additional uncertainty.

Sources: mag-inc.com [1]

Answers use the stated model and units. Examples are calculated values, not measurements or component ratings.