My favorites

Coilcraft 0402HP vs 0402DC: Q, SRF and RF Inductor Selection

0402DC is not uniformly higher-Q than 0402HP. At 12nH, the current manufacturer tables show Q 69 vs 66 at 900MHz, but 98 vs 100 at 1.7GHz. Select using the application frequency, matching network and qualified full ordering code—not a family-wide superiority claim. [1][2]

1. Compare at the same frequency and nominal value

This worked example compares 12nH families at 25°C. It does not establish the result for 10nH or every other inductance. Q is a frequency-dependent typical measurement; different frequencies are not an equal-condition comparison. The Q fixture also differs between these two family tables. [1][2]

2. Read Q, effective inductance and SRF together

HP lists typical inductance of 12nH at 900MHz and 12.6nH at 1.7GHz. The DC summary table does not tabulate those two effective-inductance values; use its curves or S-parameters rather than copying nominal 12nH into those cells. DC lists typical SRF 6.6GHz versus HP 4.4GHz. SRF alone does not establish Q or insertion loss at the operating frequency. [1][2]

3. Keep electrical and thermal test conditions attached

DC nominal inductance is measured at 250MHz using HP4287 / SMD-F. Q uses HP4991A / HP16197 for DC and HP4287A / HP16197 for HP; both SRF notes use HP8722ES / SMD-D. HP thermal current is at a 15°C rise; DC uses 40°C rise, both at 25°C ambient. Their 1200mA and 1450mA ratings are not directly comparable thermal limits. [1][2]

4. Validate a replacement on the intended PCB

Check the exact suffix, tolerance, termination and current revision of the mechanical/land-pattern drawings. Simulate using the relevant frequency model, then measure matching, insertion loss, detuning, bias and temperature on the intended PCB. Similar package codes do not prove electrical interchangeability.

5. 10nH at 900MHz and the high-inductance boundary

Coilcraft describes about 25% higher Q for 0402DC at 10nH and 900MHz. The current family tables list typical Q 77 for DC and 62 for HP (about 24.2% from rounded values). This is a specific operating point, not a board-level improvement guarantee. DC spans 0.8–120nH, while HP spans 1.0–220nH. Above 120nH, the DC family does not provide a same-nominal-value option. Consult the exact suffix, models and PCB measurements. Sources checked 2026-11-16. [3][4]

Parameter review table

Parameter / stated example and condition0402HP reference [1][3]0402DC reference [2][4]
Nominal inductance12nH12nH
Q typical @900MHz6669
Q typical @1.7GHz10098
Q typical @2.4GHzNot tabulated in summary100
L typical @900MHz / 1.7GHz12 / 12.6nHNot tabulated in summary; inspect curves
SRF typical4.4GHz6.6GHz
DCR maximum0.10Ω (100mΩ)81mΩ
Irms at 25°C ambient1200mA, 15°C rise1450mA, 40°C rise
Q instrument / fixtureHP4287A / HP16197HP4991A / HP16197
SRF instrument / fixtureHP8722ES / SMD-DHP8722ES / SMD-D
10nH family Q typical @900MHz [3][4]6277
Published family inductance range [3][4]1.0–220nH0.8–120nH

Put the review into practice

For a 12nH matching network at 900MHz, the DC family has the higher tabulated typical Q. At 1.7GHz the HP value is higher. Even within this one example the ordering reverses. Neither result establishes measured board performance or the best 10nH choice; review curves and the actual network.

Frequently asked questions

Is the 10nH Q improvement at 900MHz enough to approve a change?

No. Coilcraft describes about 25% higher typical Q at that specific point; the rounded table values give about 24.2%. Validate matching, loss, temperature and the exact ordering codes on the intended PCB.

Can Q at 900MHz be directly compared with Q at 1.7GHz?

They describe different operating points. Compare at the same frequency and retain the test fixture and typical/minimum definitions.

Does changing HP to DC require PCB matching validation?

Yes. Revalidate the actual matching network and parasitics using an appropriate model and board measurements. Equal nominal inductance and package size do not certify a drop-in replacement.

What if the original inductance is above 120nH?

The stated 0402DC range ends at 120nH, while 0402HP reaches 220nH. Do not label DC a same-value replacement outside its published range.

Exact-part examples and evidence

0402HP-12NXJR

The Magdir record retains its historical full suffix. The current 12N family table below is a research reference; it does not certify Q or SRF for this unmatched suffix. Confirm the exact ordering code with Coilcraft before assigning family data to this record.

Open catalogue recordOpen cited documentation

0402DC-12NXJRW

Open the exact catalogue record, then check the current manufacturer ordering table, tolerance, termination and packaging. The comparison uses 12N family values and does not approve a footprint-compatible substitute.

Open catalogue recordOpen cited documentation

0402DC-5N7XJRW

Additional exact catalogue entry for navigating the DC series. This is a 5.7 nH example, not a same-L replacement for either 12 nH example above. No Q, SRF or current value is transferred from the 10 nH or 12 nH comparisons; confirm its full suffix with the original ordering table.

Open catalogue recordOpen cited documentation

Original technical references

  1. Coilcraft — 0402HP-12N family measurements and test notes [1]
  2. Coilcraft — 0402DC-12N family measurements and test notes [2]
  3. Coilcraft — 0402HP series comparison and 10nH table [3]
  4. Coilcraft — 0402DC series range and 10nH table [4]

Check the latest documentation for the full ordering code and validate the intended circuit before ordering or substituting a part.

Explore the guides

Engineering tools and catalogue

Send a selection inquiry